This article provides a comprehensive look at bevel gears, include the following information:
Bevel gears are toothed, rotating devices designed to transmit mechanical energy or power between intersecting shafts, often at right angles. They alter the axis of rotation and can adjust torque levels, either enhancing or reducing it, while inversely impacting angular speed.
Structurally, a bevel gear is akin to a truncated cone, featuring teeth along its sloped surface that engage with the teeth of other gears. The gear imparting power to the shaft is termed the driver gear, whereas the one receiving this power is known as the driven gear. The driver and driven gears generally differ in their tooth count to generate a mechanical advantage. The gear ratio represents the number of teeth on the driven gear relative to those on the driver gear, and mechanical advantage is the ratio of output torque to input torque. This relationship is illustrated by the following formula:
The mechanical advantage (MA) is a function of several parameters, including the torques (Ï„b and Ï„a), radii (rb and ra), and teeth numbers (Nb and Na) of the driven and driver gears. The equation clearly indicates that increasing the teeth on the driven gear yields higher output torque.
In contrast, a boost in mechanical advantage results in a reduction in the driven gear's output speed. This dynamic is articulated by this equation:
ωa and ωb represent the angular speeds of the driver and driven gears, respectively. Typically, a 10:1 gear ratio is ideal for a bevel gear set, whereas a 1:5 ratio is advised for elevating the driven gears' speed.
It is important to remember that bevel gears come as matched pairs and should not be interchanged. Bevel gears are precisely assembled to handle transmission of both thrust and radial loads, differentiating them from spur gears, which primarily manage radial loads. The assembly of all bevel gears is performed at an optimal position to ensure peak performance.
Efficiency is defined as the ratio of output power to input power. This differs from mechanical advantage, which focuses on amplifying forces or torques at the expense of speed. In bevel gears, power loss during transmission is primarily due to friction between the teeth surfaces and the loads on the bearings or housing. The efficiency of various types of bevel gears, compared to other gear types, is summarized in the table below.
| Type of Gear | Approximate Range of Efficiency | Type of Load Imposed in Bearings |
|---|---|---|
| Straight Bevel Gear | 97 – 99.5% | Radial and thrust |
| Spiral Bevel Gear | 97 – 99.5% | Radial and thrust |
| Zerol Bevel Gear | 97 – 99.5% | Radial and thrust |
| Hypoid Bevel Gear | 90 – 98% | Radial and thrust |
| External Spur Gears | 97 – 99.5% | Radial |
| Internal Gears | 97 – 99.5% | Radial |
| Worm Gear | 50 – 90% | Radial and thrust |
Bevel gears come in various types, classified by their tooth profile and orientation. More complex types, such as spiral and hypoid bevel gears, have emerged from advancements in manufacturing processes like CNC machining.
A straight bevel gear is the most basic type of bevel gear, featuring teeth arranged in a straight line that intersects at the gear's axis when extended. The teeth are tapered, with the outer part, or heel, being larger than the inner part, or toe. Straight bevel gears have instantaneous lines of contact, which allows for greater tolerance in mounting. However, they are prone to vibration and noise, limiting their use to low-speed and static loading applications. A common application of straight bevel gears is in the differential systems of automotive vehicles.
Straight bevel gears are also the easiest to manufacture. The earliest method involved using a planer with an indexing head. More efficient manufacturing techniques have been developed, including the Revacycle and Coniflex systems used by Gleason Works.
A spiral bevel gear is a more complex type of bevel gear, distinguished by its curved and oblique teeth. Unlike the straight teeth of bevel gears, the spiral tooth orientation provides more overlap between teeth, leading to gradual engagement and disengagement. This smoother operation results in reduced vibration and noise. Additionally, the increased contact area allows spiral bevel gears to handle higher loads, making them capable of achieving greater load capacities while being smaller in size compared to straight bevel gears with equivalent capacity.
One drawback of spiral bevel gears is the increased thrust load they generate, which necessitates the use of more costly bearings. Typically, a rolling element thrust bearing is required for spiral bevel gear assemblies. Additionally, spiral bevel gears are manufactured in matched sets, and gear sets with the same design are not interchangeable unless specifically made to be interchangeable. These gear sets can be either right-hand or left-hand.
Spiral bevel gear teeth are generally shaped using gear generating machines, a process that ensures high precision and finish. To achieve the desired tooth bearing, lapping is also performed to refine the teeth further.
Zerol bevel gears are a variation of straight bevel gears, developed by Gleason Works. Unlike straight bevel gears, Zerol bevel gears feature teeth that are curved along their length. They resemble spiral bevel gears in profile, but they differ in their spiral angle: Zerol bevel gears have a 0° spiral angle, whereas spiral bevel gears typically have a 35° spiral angle.
Similar to straight bevel gears, Zerol bevel gears do not generate significant thrust loads, allowing the use of plain contact bearings. They can be used as substitutes for straight bevel gears without requiring changes to the housing or bearings. Additionally, the curvature of Zerol bevel gear teeth provides a slight overlap, similar to that of spiral gears, resulting in smoother operation compared to straight bevel gears.
Zerol bevel gear teeth are produced using a rotary mill cutter, which imparts a lengthwise curvature to the teeth. These gears are manufactured with high precision and are often finished through lapping or grinding to achieve the desired surface quality.
A hypoid bevel gear is a specialized type of bevel gear where the shafts are neither intersecting nor parallel. The offset between the two gear axes is referred to as the "offset." The teeth of hypoid bevel gears are helical, similar to those in spiral bevel gears. When a hypoid bevel gear has no offset, it essentially functions as a spiral bevel gear. The manufacturing and shaping processes for hypoid bevel gears are comparable to those used for spiral bevel gears.
Due to the offset, the spiral angle of the smaller gear (pinion) in a hypoid bevel gear set can be greater than the spiral angle of the larger gear. This means that the number of teeth on the gears does not directly correlate with their pitch diameters or theoretical operating diameters. This allows for the use of larger pinions with specific sizes of driven gears, which strengthens the pinion and provides a higher contact ratio with the larger gear. As a result, hypoid gears can transmit more torque and operate at higher gear ratios. Additionally, the offset allows for bearings to be positioned on both sides of the gears since their shafts do not intersect. However, an increased offset can reduce the overall efficiency of the gear system.
Hypoid gears run more smoothly and produce less vibration compared to spiral gears. However, they come with a drawback: the significant amount of sliding that occurs across the teeth's face can increase friction and wear. This necessitates the use of specialized lubricating oils to ensure smooth operation and longevity.
Miter gears are a type of bevel gear with a gear ratio of 1:1, meaning both the driver and driven gears have the same number of teeth. As they do not provide a mechanical advantage, their primary function is to change the direction of rotation. Typically, miter gears have axes that intersect perpendicularly. However, in some assemblies, shafts may intersect at various angles, known as angular miter bevel gears. These angles can range from 45° to 120°. Miter bevel gears can have teeth that are straight, spiral, or Zerol.
To gain a clearer understanding of gears and gear systems, it's essential to familiarize oneself with key terminology. The terms listed below describe various aspects of gears and their tooth profiles and are applicable to all types of gears, not just bevel gears.
The smaller gear in a bevel gear set that drives the larger gear.
The larger gear in a bevel gear set that is driven by the smaller pinion gear.
Also known as circular pitch, this is the distance between corresponding points on adjacent teeth of the same gear.
The diameter of the pitch circle, which is a critical design parameter for determining tooth thickness, pressure angles, and helix angles of the gear.
The ratio of the number of teeth to the pitch diameter of a gear.
The angle between the face of the pitch surface and the axis of the shaft.
The imaginary truncated cone where the base diameter corresponds to the pitch circle.
The angle between the line of force of the meshing teeth and the tangent to the pitch circle at the contact point. For proper meshing, gears must have the same pressure angle. The recommended pressure angle for straight bevel gears is 20°.
The angle between the shafts of the driver and driven gears.
The upper outline of the gear teeth, extending from the pitch circle to the top of the teeth.
The lower outline of the gear teeth, extending from the pitch circle to the bottom of the teeth.
The radial distance between the addendum and dedendum circles. Due to the slight taper of bevel gear teeth, this depth is not constant along the tooth. Addendum and dedendum angles are used to describe the teeth more accurately than the circles.
The angle between the top surface of the teeth (top land) and the pitch surface.
The angle between the bottom surface of the teeth (bottom land) and the pitch surface.
The variation in tooth depth along the face, measured perpendicular to the pitch surface.
The variation in space width along the face, measured on the pitch surface.
The variation in tooth thickness measured on the pitch surface.
The total depth of the teeth plus the clearance value.
The difference between the addendum of one gear and the dedendum of the mating gear.
The space between the mating gear teeth that exceeds their thickness. Different types of backlash are defined based on movement orientation:
The arc along the pitch circle.
The space between the surfaces of mating teeth.
The angular movement described by the backlash.
The linear movement perpendicular to the axis.
The linear movement parallel to the axis.
Backlash is crucial for preventing gear jamming due to contact. It allows lubricants to enter and protect the mating teeth surfaces and accommodates thermal expansion during operation.
The relationship between these terms is illustrated in the table of equations below.
| To Find | Having | Formula |
|---|---|---|
| Pitch diameter of pinion | Number of pinion teeth and diametral pitch | d = Np / Pd |
| Pitch diameter of gear | Number of gear teeth and diametral pitch | D = Ng / Pd |
| Pitch angle of pinion | Number of pinion teeth and number of gear teeth | γ = tan^-1(Np / Ng) |
| Pitch angle of gear | Pitch angle of pinion | Γ= 90°-γ |
| Outer cone distance of pinion and gear | Gear pitch diameter and pitch angle of gear | Ao = D / (2sinΓ) |
| Circular pitch of pinion and gear | Diametral pitch | p = 3.1416 / Pd |
| Dedendum angle of pinion | Dedendum of pinion and outer cone distance | δp = tan-1(bop / Ao) |
| Dedendum angle of gear | Dedendum of gear and outer cone distance | δg = tan-1(bog / Ao) |
| Face angle of pinion blank | Pinion pitch angle and dedendum angle of gear | γo = γ + δg |
| Face angle of gear blank | Gear pitch angle and dedendum angle of pinion | Γo = Γ + δp |
| Root angle of pinion | Pitch angle of pinion and dedendum angle of pinion | γr = γ - δp |
| Root angle of gear | Pitch angle of gear and dedendum angle of gear | Γr = Γ - δg |
| Outside diameter of pinion | Pinion pitch diameter of gear, pinion addendum, and pitch angle of pinion | do = d +2aop cosγ |
| Outside diameter of gear | Pitch diameter of gear, gear addendum, and pitch angle of gear | Do = D + 2aog cosΓ |
| Pitch apex to crown of pinion | Pitch diameter of gear, addendum, and pitch angle of pinion | xo = (D/2) - aop sinγ |
| Pitch apex to crown of gear | Pitch diameter of pinion, addendum, and pitch angle of gear | Xo = (d/2) - aog sinΓ |
| Circular tooth thickness of pinion | Circular pitch and gear circular tooth thickness | t = p - T |
| Chordal thickness of pinion | Circular tooth thickness, pitch diameter of pinion and backlash | tc = t - (t3/6d2) - (B/2) |
| Chordal thickness of gear | Circular tooth thickness, pitch diameter of gear and backlash | Tc = T - (T3/6D2) - (B/2) |
| Chordal addendum of pinion | Addendum angle, circular tooth thickness, pitch diameter, and pitch angle of pinion | acp=aop + (t2 cosγ / 4d) |
| Chordal addendum of gear | Addendum angle, circular tooth thickness, pitch diameter, and pitch angle of gear | acg=aog + (T2 cosΓ / 4D) |
| Tooth angle of pinion | Outer cone distance, tooth thickness, dedendum of pinion, and pressure angle |
(3.438/Ao)(t/2)+bop tanφ
min |
| Tooth angle of gear | Outer cone distance, tooth thickness, dedendum of gear, and pressure angle |
(3.438/Ao)(T/2)+bog tanφ
min |
| To Find | Having | Formula |
|---|---|---|
| Pitch diameter of pinion | Number of pinion teeth and diametral pitch | d = Np / Pd |
| Pitch diameter of gear | Number of gear teeth and diametral pitch | D = Ng / Pd |
| Pitch angle of pinion | Number of pinion teeth and number of gear teeth | γ = tan-1(Np / Ng) |
| Pitch angle of gear | Pitch angle of pinion | Γ= 90°-γ |
| Outer cone distance of pinion and gear | Pitch diameter of gear and pitch angle of gear | Ao = D / (2sinΓ) |
| Circular pitch of pinion and gear | Diametral pitch | p = 3.1416 / Pd |
| Dedendum angle of pinion | Dedendum of pinion and outer cone distance | δp = tan-1(bop / Ao) |
| Dedendum angle of gear | Dedendum of gear and outer cone distance | δg = tan-1(bog / Ao) |
| Face angle of pinion blank | Pitch angle of pinion dedendum angle of gear | γo = γ + δg |
| Face angle of gear blank | Pitch angle of gear and dedendum angle of pinion | Γo = Γ + δp |
| Root angle of pinion | Pitch angle of pinion and dedendum angle pinion | γr = γ - δp |
| Root angle of gear | Pitch angle of gear and dedendum angle of gear | Γr = Γ - δg |
| Outside diameter of pinion | Pitch diameter, addendum, and pitch angle of pinion | do = d +2aop cosγ |
| Outside diameter of gear | Pitch diameter, addendum, and pitch angle of gear | Do = D + 2aog cosΓ |
| Pitch apex to crown of pinion | Pitch diameter of gear, pitch angle, and addendum of pinion | xo = (D/2) - aop sinγ |
| Pitch apex to crown of gear | Pitch diameter of gear, pitch angle, and addendum of gear | Xo = (d/2) - aog sinΓ |
| Circular tooth thickness of pinion | Circular pitch of pinion and circular pitch of gear | t = p - T |
There are four main methods of manufacturing gears. These are metal cutting, casting, forming, and powder metallurgy. Metal cutting is the most widely used process because of its dimensional accuracy. The second two, casting and forming, are used in special circumstances- for example, producing a large gear through casting, which reduces machining expenses by casting closer to the final shape. Another form of casting, known as injection molding, is used to manufacture plastic gears. Forming, on the other hand, can take the form of cold drawing or forging. Cold drawing involves a stock pulled or extruded into a series of dies to form the shape of the gear. Forging presses the stock against dies with the desired tooth configuration. Because of work hardening through continuous deformation, the resulting gear is harder, with a more contoured grain flow.
Gear cutting can be categorized into four distinct methods, summarized as follows:
Due to the conical shape of bevel gears, which introduces both depth and width taper, not all cutting techniques are applicable. For bevel gear cutting, metal cutting methods are generally classified into two categories: face hobbing and face milling.
Face Hobbing: Face hobbing is a continuous indexing gear generation process. This involves groups of cutting blades that cut all teeth gradually until the desired depth is achieved. As one blade group cuts one tooth, the next blade group enters the next tooth space. The cutting tool and the workpiece rotate simultaneously.
Face Milling: Face milling is a single indexing method where the cutting wheel or tool is fed to cut one tooth space and is then indexed to the next tooth location. The cutting tool and the workpiece are synched together to perform the cut. Each tooth is milled until all teeth are cut to the required depth. Face milling can be done by a two-tool planer, double rotary blade, single row mill cutter, or five-axis CNC milling machines.
Bevel gears offer a straightforward and effective solution for altering the axis of rotation in drivetrains. The choice of bevel gear type, as well as the manufacturing and finishing techniques, depends on the specific application. Below are some common applications of bevel gear systems.
The most popular application of bevel gears is in the differential of an automotive vehicle. The differential is the part of the front or rear axle assembly that allows the wheels to rotate at different speeds. This allows the vehicle to turn corners while maintaining handling and traction. The driveshaft is connected to the hypoid gear assembly, which consists of a pinion and a ring gear. The ring gear is mounted to the carrier with other bevel gears in a planetary gear train.
Bevel gears are utilized in heavy machinery for both propulsion, similar to an automotive differential system, and for driving auxiliary units.
In the aviation industry, bevel gears are employed in power transmission systems for helicopters and aircraft accessory gearboxes.
An example of industrial plant equipment that uses bevel gears is cooling tower fans. The motor is usually mounted at the deck of the cooling tower with the shaft axis oriented horizontally. A gearbox assembly reduces the speed and increases the torque while also reorienting the axis of rotation vertically.
In marine transmissions, bevel gears are frequently utilized as part of the stern drive system. Typically, two bevel gear sets are employed between the engine and the propeller.
A gear is a particular kind of simple machine that controls the strength or direction of a force. A gear train is made up of multiple gears that are combined and connected by their teeth. These gear trains allow energy to move from...
A planetary gear is an epicyclic gear that consists of a central gear, referred to as the sun gear and serves as the input gear, which has three or more gears that rotate around it that are referred to as planets...
A plastic gear is a toothed wheel made up of engineering plastic materials that work with others to alter the relation between the speed of an engine and the speed of the driven parts. The engineering plastic materials used in manufacturing plastic gears can be...
A spur gear is a cylindrical toothed gear with teeth that are parallel to the shaft and is used to transfer mechanical motion and control speed, power, and torque between shafts. They are the most popular types of cylindrical gears and...
A worm gear is a staggered shaft gear that creates motion between shafts using threads that are cut into a cylindrical bar to provide speed reduction. The combination of a worm wheel and worm are the components of a worm gear...
A rotary circular machine with a tooth in its structure and is used to transfer torque and speed from one shaft to another is called a gear. Gears are also known as cogs and have cut teeth in the cogwheel or gear wheel...
Ball screws are mechanical linear actuators that consist of a screw shaft and a nut that contain a ball that rolls between their matching helical grooves. The primary function of ball screws is to convert rotational motion to linear motion. Ball nuts are used in...
A lead screw is a kind of mechanical linear actuator that converts rotational motion into linear motion. Its operation relies on the sliding of the screw shaft and the nut threads with no ball bearings between them. The screw shaft and the nut are directly moving against each other on...
Powder metallurgy is a manufacturing process that produces precision and highly accurate parts by pressing powdered metals and alloys into a rigid die under extreme pressure. With the development and implementation of technological advances...
Thread rolling is a type of threading process which involves deforming a metal stock by rolling it through dies. This process forms external threads along the surface of the metal stock...