AC DC Power Supply
Power supplies are electrical circuits and devices that are designed to convert mains power or electricity from any electric source to specific values of voltage and current for the target device...
DC Power Supply: Basics, Types and Applications
Introduction
This article will take an in-depth look at DC/DC power supplies:
- What is a DC/DC Power Supply?
- Types of DC/DC Power Supplies
- Basics of DC/DC Power Supplies
- Mounting and Package Choices
- Applications of DC/DC Power Supplies
- And much more...
Chapter One – What is a DC Power Supply?
A DC/DC Converter represents a type of power supply utilizing a direct current (DC) voltage input, in contrast to alternating current (AC) voltage. Its main role is to deliver a consistent output voltage that is ideal for powering electronic and electrical equipment. Unlike AC voltage, a DC voltage cannot be modified to higher or lower levels using a transformer.
Chapter Two – How do different power inputs affect a DC power management subsystem?
A DC power supply typically has two primary power inputs:
AC Input
An AC input can be rectified and filtered to produce a DC voltage, which is then fed into a regulator circuit to generate a stable DC output voltage. The output can vary from less than a volt to over 1000 volts.
DC Input
A DC power supply can also accept DC voltages as input, commonly 5V, 12V, 24V, or 48V. The output voltage, which can range from less than a volt to over 1000 volts DC, is then generated. Additionally, power inputs for a DC power management subsystem can include batteries or harvested energy sources such as solar cells and fuel cells, which convert other forms of energy into electrical power.
Battery Input
The DC power management subsystem is typically integrated into the electronic system of portable equipment. Portable devices often include an AC adapter, a power unit that plugs into an AC outlet and provides a DC output voltage to power the device. If the system includes a battery, the AC adapter can also be used to recharge it.
Ultralow Voltage Input
Small amounts of energy from sources like solar power, thermal energy, wind energy, or kinetic energy can be harvested by a power converter capable of operating with ultralow voltage inputs. Once collected, this energy is stored for future use as a power source.
Chapter Three – What does the block diagram of a regulated DC power supply illustrate?
As covered in the previous chapter, a DC power supply can be derived from an AC line. Most electrical and electronic circuits need a constant DC voltage source, regardless of input variations. While DC batteries can serve as an input, they are costly and require periodic replacement. Therefore, it is essential to first convert an AC input into a DC voltage source and then regulate it for consistent performance. This conversion process involves four major steps and is often illustrated by a diagram known as the Regulated DC Power Supply Block Diagram.
Step Down Transformation
A step-down transformer is used in the first step of AC-DC voltage conversion. It is a device that converts a high primary voltage to a lower value (secondary voltage). A step-down transformer has two coil windings: primary and secondary, with the former having more coil winding turns than the latter.
The primary winding connects to the main AC line, while the secondary winding, although electrically isolated, is electromagnetically coupled to the primary winding.
Step-down transformers can be classified into three categories:
Single-Phase Step-down Transformer
This type of step-down transformer reduces both the current and input voltage ratings, resulting in a lower current and voltage output.
Center-Tapped Step-down Transformer
This type of step-down transformer features a primary winding and a secondary winding with a center tap. As a result, the voltage output will have a center split, such as 12V to 0 to 12V.
Multi-Tapped Step-down Transformer
This type of step-down transformer uses multiple taps on the secondary winding to achieve various desired output voltages (e.g., 0-12V, 0-18V). The multiple taps allow for different output voltage options.
The transformer output is then fed into the rectifier circuit for further processing.
Rectification
The second step in the AC-DC voltage conversion process is rectification. During this stage, the AC voltage is converted into its DC equivalent.
A rectifier is used to perform this process. It is an electronic circuit that consists of diodes.
Rectifiers are primarily categorized into controlled and uncontrolled types. Controlled rectifiers use SCRs (Silicon Controlled Rectifiers) or thyristors, whereas uncontrolled rectifiers use diodes.
Additionally, rectifiers can be classified as either half-wave or full-wave rectifiers.
A half-wave rectifier circuit employs a single diode to convert half of the AC input signal into a pulsating DC output, while the other half of the signal is discarded. There are two types of half-wave rectifiers:
- Positive Half-Wave Rectifier -
- In this type of rectifier circuit, the positive half cycle of the AC is converted into DC while the negative half is lost.
- Negative Half-Wave Rectifier -
- In this type of rectifier circuit, the negative half cycle of the AC is converted into DC while the positive half is lost.
Three-phase rectification, also known as polyphase rectification, involves using three single-phase rectifiers connected together. This method is employed when single-phase rectifiers do not deliver adequate power.
Multi-phase rectifiers are designed to reduce harmonics in three-phase systems. They typically consist of two 6-pulse rectifiers connected in series with 12 diodes, feeding a DC bus. By staggering the current waveforms, they improve waveform quality and cancel out the 5th and 7th harmonics. This makes the 11th harmonic the most significant, keeping voltage harmonic distortion within acceptable levels.
The multi-phase rectifier configuration can extend to an 18-pulse rectifier, which involves three sets of 6-pulse rectifiers. However, as additional rectifiers are added, both the cost and the physical footprint increase.
A full-wave rectifier circuit uses multiple diodes to convert both half-cycles (positive and negative) of the AC signal into DC, effectively doubling the output voltage. There are two types of full-wave rectifier circuits:
- Bridge Rectifier -
- It has four diodes that allow conversion of both positive and negative half cycles of AC input into DC. The output voltage from this rectifier could be almost twice that of a full-wave center-tapped transformer rectifier.
- Center-Tap Rectifier -
- This full-wave rectifier circuit utilizes a center-tapped transformer to which two diodes are connected. Each of the diodes uses the half-cycle of the AC input. Since the AC input provides power to both the halves, this circuit is expected to have high output and efficiency.
DC Filtration
After rectification, the output is a pulsating DC voltage with significant ripple content. To smooth out these ripples, a process called DC filtration is used to refine the waveform.
Common filters employed for this purpose include capacitor filters, LC filters, choke input filters, and π-type filters.
In a capacitor filter, the capacitor charges as the instantaneous DC voltage rises to its peak. When the voltage then decreases, the capacitor gradually discharges through the regulator.
Regulation
The final step is to stabilize the output DC voltage to a constant value using a regulator.
A regulator ensures that fluctuations in the output DC voltage—caused by changes in the AC mainline input, load current, or other variable factors such as temperature—are eliminated.
The following types of regulators can be used in this step:
- Transistor series regulator
- Fixed and variable IC regulator
- Zener diode
Chapter Four – What are the different designs for DC power supplies?
Regulated power supplies and unregulated power supplies are the major classifications of DC power supplies. Regulated power supplies are subdivided into two types: linearly regulated and switch mode. Switch-mode power supplies can be primary or secondary switch mode.
The following list describes each type and design of DC power supply.
Unregulated Power Supplies
An unregulated power supply uses the AC mainline as its input. The AC voltage first passes through a step-down transformer, which reduces the voltage. This lower secondary voltage is then rectified and converted into DC. The output voltage from the rectifier is smoothed by a capacitor. As the name implies, unregulated power supplies lack a regulator, meaning any fluctuations in the mainline directly affect the output voltage.
Unregulated power supplies feature a simple design, which contributes to their durability and results in a typical efficiency of around 80%.
They are primarily used in electromechanical applications that do not require precise output voltages, such as supplying power to contactors.
Main advantages include:
- Highly efficient
- Heavy-duty
- Cost-efficient
Disadvantages include:
- Bulk size
- High residual ripple
- Without DC supply (input)
Linearly Regulated Power Supplies
Linearly regulated power supplies use the AC-DC conversion process described in Chapter 3.
The AC mains voltage is first stepped down to a lower level using a transformer, then rectified and filtered. The final step involves regulating the smoothed DC voltage, typically with a power transistor, to maintain a constant output.
In linearly regulated power supplies, the power transistor functions as a variable resistor.
Energy losses occur as the current passes through the power transistor, with the lost energy being dissipated as heat. Therefore, proper ventilation is necessary for the power supply.
Due to these energy losses, linearly regulated power supplies generally have an efficiency of about 50%.
For applications requiring very precise output voltage, such as highly accurate medical devices, linearly regulated power supplies are often used.
Main advantages include:
- Short regulation times
- Small residual ripple
- Simple circuitry
Disadvantages include:
- Low efficiency
- Large size
- Without DC supply (input)
Primary Switch Mode Power Supplies
Primary switch mode power supplies start with rectifying the AC mains, followed by filtering and chopping/switching processes.
Chopping a DC voltage involves periodically switching it at a frequency of 40-200 kHz using a power transistor.
Unlike in linearly regulated power supplies, where power transistors act as variable resistors, in primary switch mode power supplies, they function as switches.
During the chopping/switching phase, a square-wave AC voltage is generated, which is then fed into a high-frequency transformer in the secondary circuit. The voltage is subsequently rectified and smoothed again.
The chopping rate can be adjusted based on the load to control the amount of energy transferred to the secondary circuit.
Because high-frequency AC voltage is used, transformers in primary switch mode power supplies can be smaller compared to those needed for low-frequency transformations.
These power supplies can handle a wide range of input voltages, including DC, as the input voltage does not directly impact the output voltage.
A short-time buffer of up to 200 ms can be included to handle mains voltage interruptions. However, the buffering time is limited by the size of the capacitor.
While a larger capacitor allows for longer buffering times, it is not ideal for small power supplies. Therefore, the power supply should be optimized to balance buffering time and capacitor size.
Primary switch mode power supplies are commonly used in both electronics and electromechanical applications.
Main advantages include:
- Small size
- Light weight
- Wide input voltage range
- Easy to regulate
- Highly efficient
- DC supply
- Buffering in case of mains voltage breakdown
Disadvantages include:
- Complex circuitry
- Mains pollution
- High frequency requires interference suppression measures
- Expensive
Secondary Switch Mode Power Supplies
Secondary switch mode power supplies are similar to primary switch mode power supplies, but the chopping occurs on the secondary side.
As a result, a larger transformer is needed to convert the 50/60 Hz mains voltage.
However, mains pollution is reduced since the transformer also functions as a filter.
Main advantages include:
- Highly efficient
- Easy to regulate
- Wide input voltage range
- Low mains pollution
Disadvantages include:
- Bulk size
- No DC supply (input)
- Expensive
In industrial applications, the primary switch mode power supply is the most commonly used type due to its wide input voltage range, high efficiency, and compact size.
Applications of a DC/DC Power Supplies
DC/DC power supplies are integral to many products, as electronic devices typically use DC power. This includes portable electronics like laptop computers and mobile phones, which are powered by batteries. These devices often contain multiple small circuits, each with specific voltage requirements that may differ from the battery or external supply voltage, which is frequently either higher or lower. Larger DC/DC power supplies are also used to optimize power output from photovoltaic systems and to charge batteries. Many DC/DC power supplies, such as those used for LEDs, are designed to regulate the voltage output.
When selecting a power supply for new engineering applications or upgrading existing installations, key factors to consider include efficiency, regulation time, weight and size, residual ripple, cost, and application fields.
Leading Manufacturers and Suppliers
Chapter Five – What are DC-DC Converters?
A DC-DC converter is a type of power supply that uses DC voltage as its input. Its primary function is to provide a regulated output voltage for various electrical and electronic applications. Unlike AC voltage, which can be altered using a transformer, DC voltage cannot be changed between different levels using a transformer. Instead, a DC-DC converter serves this purpose, functioning similarly to a transformer.
Much like transformers, DC-DC converters adjust the input energy to a different impedance level. The converter itself does not generate energy; all output power is derived from the input power. However, in practical applications, some energy is lost within the converter due to component inefficiencies. Thanks to advances in components and circuit design, modern DC-DC converters can achieve efficiencies of up to 90%.
DC-DC converters are categorized into two types:
Isolated vs Non-Isolated Configurations
DC/DC power supplies can be found in either non-isolated or isolated configurations. In isolated converters, the output and input circuits are galvanically isolated, meaning there is no direct DC path between them. This isolation is crucial for separating the output and input circuitry to ensure safety from dangerous voltages or to reduce electrical noise. Isolated converters can also provide multiple output voltages from a single unit.
Non-isolated converters, on the other hand, have a direct DC connection between the output and input through a common ground. These converters are generally smaller and less expensive than isolated ones. Non-isolated converters can also produce a negative voltage output from a positive voltage input.
Non-Isolating Converters
This type of DC-DC converter is used for stepping up or down the voltage by a small ratio (less than 4:1).
Non-isolating converters do not provide dielectric isolation between the input and output.
Examples of such converters include 24V/12V voltage reducers, 5V/3V reducers, and 1.5V/5V step-up converters.
Non-isolating converters have five types:
- Buck Converter: For voltage step-down
- Boost Converter: For voltage step-up
- Buck-Boost: For either step-down or step-up
- Cuk: For either step-down or step-up
- Charge-Pump: Also used for either voltage step-up or inversion (low power applications)
Isolating Power Converters
- When a transformer is incorporated into the powertrain of the converters, it provides isolation between the primary and secondary side and forms an isolated converter.
- A buck converter with a transformer is usually called a forward converter since the energy transfer happens when the primary side is active or conducting.
- A boost converter with a transformer is called a flyback converter, since the energy is stored in the magnetics during the primary switch ON-time and transferred to secondary or output side when the Primary Switch is OFF. Power supply companies offer isolated power converters, popularly referred to as Power Bricks.
DC-DC converters are useful in the following applications:
- Operation of car radio, CB transceiver, or mobile phone
- Stepping down of 24V DC (truck battery) to 12V DC
- Running a personal CD player
- Stepping down of 12V DC (car battery) to 3V DC
- Energizing one of the latest CPU chips
- Stepping down of 5V DC (personal computer motherboard) to 3V, 2V or less
- PC power supply application
- Stepping down of 340V DC (from rectified 240V AC power) to 5V, 12V, and other DC voltages
- Operation of electronic circuitry
- Stepping up of 1.5V (single-cell) to 5V or more
- Providing an insulation testing voltage
- Stepping up of 6V or 9V DC to 500V DC or more
- Running a car HiFi amplifier‘s circuitry
- Stepping up of 12V DC to +/- 40V
- DC-AC sine wave inverter application
- Stepping up of 12V DC to 650V DC
Chapter Six – What are the basic outputs or modes of a DC power supply?
DC power supplies have four basic outputs or modes: constant voltage, constant current, voltage limit, and current limit. They can be designed with various combinations of these outputs to suit different applications.
Constant Voltage Power Supply
- Any changes in load, line, or temperature will not affect the output voltage. Hence, a constant output voltage is supplied.
- Ideally, constant voltage power supplies would have zero output impedance at all frequencies.
- Loads are connected in series.
- There are four regulating techniques employed to provide a reasonable constant DC output voltage, and these include:
Series Regulation
The circuit includes a control element in series with a rectifier and load device, a configuration used in linear power supplies. The main advantages of series regulation are:
- Simple
- High performance
- Low power requirements
Series Regulation with Pre-Regulation
Adding a pre-regulator to a series regulator enables circuit techniques suitable for medium and high-power design applications. Pre-regulation also enhances efficiency by 10-20% by reducing power dissipation in the series regulating components. The main advantages of series regulation with pre-regulation are:
- High efficiency
- Excellent regulation
- Low ripple and noise
- Fewer series regulating transistors
Switching Regulation
Switching regulation in a basic switching supply involves a series of transistors functioning as open and closed switches. The main advantages of switching regulation are:
- Lower power dissipation
- Higher efficiency than linear types
- Low operational costs
- Smaller regulator heat sinks
- Smaller in size and weight (for high switching rate)
SCR (Silicon Controlled Rectifiers)
This regulating technique is used in high-power applications. The main advantages of SCR are:
- Low cost
- Compact
- Relatively high efficiency
Constant Current Power Supply
- Any changes in load, line, or temperature will not affect the output current. Hence, a constant output current is supplied.
- Ideally, constant current power supplies would have an infinite output impedance at all frequencies.
- A change in load resistance is accommodated by the constant current power supply such that the output voltage is changed by just the right amount to remain the output current constant.
- Common applications include semiconductor testing, circuit design, and fixed current supply to focus coils.
- Loads are connected in series.
Voltage Limit
Like the constant voltage power supply, but it has less precise regulation characteristics.
Current Limit
Like the constant current power supply, but it has less precise regulation characteristics.
Chapter Seven – What are the different types of DC/DC power supplies?
There are several types of DC/DC converters available, including buck, boost, non-inverting buck-boost, and flyback converters. Buck converters produce a lower output voltage than the input voltage, while boost converters provide an output voltage higher than the input. Buck-boost converters can deliver an output voltage that is either above or below the input voltage, making them ideal for battery-powered applications where extended battery life is critical.
Flyback converters are used for lower power applications, typically below 100 W. They operate by storing energy in the magnetic component of a power supply when the power switch is ON and delivering it to the output when the switch is OFF. Flyback converters also offer isolation between the input and output voltages, which is useful for polarity inversion and reducing system noise.
These four types of converters are the most commonly used. The choice of which to use depends on factors such as size, performance, cost, and specific application requirements.
Basics of DC/DC Power Supplies
The advancement of integrated circuits with sophisticated features allows power supplies to operate at higher switching frequencies. This capability enables designers to reduce the size of magnetic components, such as transformers and output filter inductors, in switching power supplies.
Higher switching frequencies facilitate the rapid replenishment of a capacitor’s charge, allowing the use of smaller and fewer output capacitors while achieving fast and precise dynamic output performance. The commercialization of wide band gap power semiconductors, such as silicon carbide (SiC) and GaN transistors, supports higher switching frequencies with lower switching losses. This development enables power supply designers to achieve higher power densities compared to those possible with Silicon MOSFETs.
Basic Switching Topologies
A power supply includes a switching system that divides a constant power source into controllable increments of energy. This is followed by a filtering system that converts these increments back into a steady, usable output power. In its simplest form, a non-isolated power supply consists of a switching transistor, a diode, an inductor, and an output capacitor. Various topologies can be created using these four circuit elements along with the necessary control circuitry to achieve the desired output voltage and efficiency.
Buck Converters
In most applications, power is distributed at higher voltage levels to maximize system efficiency. The role of the power converter is to step down the incoming voltage to a lower value required by the load. Power converters that provide an output voltage lower than the input voltage are known as buck converters.
When the switch (SW) is closed or ON, energy is transferred from Vin to the load. By adjusting the ON and OFF times, the amount of energy delivered to the output can be controlled. The ratio of the ON time to the total cycle time (ON time plus OFF time) defines the duty cycle of the power converter, which ranges from 0 to 1. The output voltage can be varied from 0 V to nearly Vin by adjusting the SW ON-time.
In a buck converter, the inductor is connected directly to the output capacitor and load. The inductor current continuously flows through the diode to the output even when the switch is open, thanks to the antiparallel connected diode. For regulated output converters, the duty cycle is controlled by the power supply controller to maintain a constant output voltage despite variations in Vin or system parameters. Non-isolated buck converters can achieve efficiencies of up to 98%.
Boost Converters
Boost converters use the same circuit elements as buck converters but arranged differently to achieve distinct performance characteristics. Boost converters increase the input voltage to provide an output voltage greater than the input voltage. In a boost converter, power is transmitted to the output through a two-step process, with the inductor serving as a temporary storage element. When the switch (SW) is closed, current flows into the inductor, and the longer the switch remains ON, the more magnetic energy is stored.
The diode prevents current from flowing back from the load, while the output capacitor maintains the output voltage. When the switch is opened, the energy stored in the inductor's magnetic field flows through the diode, recharges the capacitor, and replenishes the energy delivered to the load when the switch is ON. This two-step process can result in high peak currents in components and affects efficiency in higher power applications, limiting its use to lower power applications.
Buck-Boost Converters
Buck-boost converters are hybrid combinations of buck and boost power converters. They integrate buck circuits on the input side and boost circuits on the output side, sharing a common inductor. This topology allows the converter to regulate the output voltage regardless of whether the input voltage is above or below the desired output voltage. The output voltage remains steady as the battery transitions from a fully charged state to a fully discharged state.
These converters are particularly popular in battery-powered applications, where maintaining a consistent output voltage is crucial even as the battery discharges to its lowest operational limit. This approach extends the runtime of battery-powered devices and ensures consistent performance throughout battery discharge.
When the input voltage (Vin) is higher than the output voltage (Vout), such as 14.5V in a fully charged 12V battery system, the circuit operates in buck mode with the boost switch (SW2) open and output Diode-2 continuously conducting. As the input voltage drops below the set Vout level during battery discharge, the input switch (SW1) remains ON, and the circuit functions as a boost converter with SW2 active to maintain the output voltage. A single control circuit manages the output voltage and determines whether buck or boost mode is needed.
Synchronous Rectifiers Used in Power Supplies
A synchronous rectifier functions similarly to a diode, allowing current to pass in one direction. When traditional power diodes are used as freewheeling or rectifying diodes, the conduction losses can be excessively high, particularly at high currents where the forward voltage (VF) is approximately 0.6 to 0.7 volts.
To reduce these losses, power MOSFETs are used instead of rectifier diodes and freewheeling diodes. This approach significantly improves power efficiency compared to standard diodes or even Schottky diodes. However, driving the power MOSFETs synchronously with the main power switches can be complex and requires specialized controllers. Despite this complexity and cost, the benefits of using synchronous rectifiers make them a popular choice in all types of switching power supplies.
Battery Eliminator
Battery eliminators are affordable, compact DC power supplies designed to replace batteries when they are not available. They are commonly used with battery-operated equipment and can provide 18V DC power to devices typically powered by automobile batteries, such as CB radios and automotive stereo systems.
Battery eliminators come equipped with an ON/OFF switch and a rotary switch to select the desired output DC voltage. Available in output voltages ranging from 1.5V to 12V, with increments of 1.5V, these units can be operated continuously and safely even in a dead short.
Constant Voltage Supply
A constant voltage supply delivers a steady and adjustable voltage and features a more complex design compared to battery eliminators. These supplies include voltage and current meters, allowing users to monitor both the voltage and current values. The output voltage can be adjusted using a knob, though some units may not be adjustable down to zero volts.
In some models, the rated current may not be available at all output voltages. In such cases, the maximum output current is proportional to the output voltage. Additionally, tie points with a current limit may be provided to connect an external digital meter for precise voltage monitoring or to other circuits.
Constant Voltage/Constant Current Supply
A constant voltage/constant current supply maintains both a constant voltage and a constant current. In constant current mode, the supply keeps the current steady regardless of the load's resistance. Typical units feature fine and coarse adjustable controls for both voltage and current. Some models use 10-turn pots, thumbwheel switches, or pushbutton switches for adjustments, eliminating the need for a meter when using thumbwheel and pushbutton switches.
This type of DC power supply has the following features:
- Remote Sensing - The voltage of the load can be measured using a high-impedance input. The power supply performs corrections for the voltage drop in the leads, bridging the supply to the load.
- Master/Slave Connections - Power supplies from the same family can be connected in parallel or series using different methods to generate higher voltages or currents.
- Remote Programming Terminal - Input terminals for a voltage or resistance are present in some power supplies that are used to control output voltage/current.
Multiple Output Supply
Multiple output DC power supplies offer more than one DC output, making them a cost-effective choice for systems that require multiple voltages.
For instance, a triple output supply is commonly used in circuit development:
- Digital Logic - where one output provides 0-6V
- Bipolar Analog Circuitry - where the other two supply outputs provide 0-20V.
With a multiple output supply, you can set each of the three outputs independently using a knob or keypad. Outputs can be turned ON and OFF either separately or all at once, enabling the entire printed circuit board to be powered simultaneously.
A typical unit also includes features such as:
- Output Operation Timer
- This allows the user to set a time interval in which the output can turn off automatically after the time set has passed.
- Voltage Limit for All Channels
- The user can set a voltage limit to avoid accidental over-voltage settings in their prototype electrical design project.
- Series or Parallel Connection
- A higher voltage or current can be achieved by connecting two volt channels in series or parallel.
- Storage Registers
- This allows the user to save 50 instrument states for easy recollection of data in repetitive testing.
- Last Power-On Settings
- In case the AC mains line fails, this type of power supply will restart when the AC power restarts, then provide the same output as the last power-on settings.
Programmable Supply
A programmable supply, known as system power supplies, are integrated into a computer operated system during production or testing.
Multi-Range Supply
A multi-range DC power supply supports various combinations of voltage and current while still delivering maximum power. Unlike conventional power supplies, which provide maximum output power only at specific fixed voltage and current ratings, a multi-range supply maintains high output power across different voltage and current combinations.
The main advantages of a multi-range supply include:
- Flexibility in output ratings
- Savings in cost and bench space
Chapter Eight – How do you determine the specifications for a DC power supply?
When selecting a DC power supply, consider the following specifications:
Constant Current and Constant Voltage Mode
DC power supplies that offer both constant current and constant voltage modes are versatile and suitable for most applications.
Output
Another important specification to consider is the power supply output. Typically, it is advisable to choose a DC power supply with an output rating higher than the current requirement, as most projects tend to incorporate additional functionalities later in the design cycle.
Regulation
Regulation refers to either load regulation or line regulation. Load regulation, typically ranging from 0.1% to 0.01%, measures the change in output voltage as the load varies. Line regulation, also usually between 0.1% and 0.01%, measures the change in output voltage in response to fluctuations in the input AC voltage.
Temperature
Most components of a DC power supply are sensitive to temperature. Therefore, it is important to check the operating temperature range and the temperature coefficient of the power supply. Ideally, a lab-quality power supply should have a temperature coefficient of 0.05% /°C.
AC Input
Three-phase power is commonly used in larger power supplies, offering greater efficiency compared to single-phase power supplies and providing a higher ripple frequency.
Additional specifications to consider include ripple and noise, tracking accuracy, and DC isolation.
Mounting and Package Choices
- DC/DC power supplies come with a variety of mounting styles and packaging.
- In applications where the power is mounted directly on a PCB there are surface mounting options or through hole mountings and single in-line pin or dual in-line pin setups.
- Chassis mounted power supplies are available for applications requiring that mounting style.
- DIN rail mounting setups are ideal for industrial applications.
- Encapsulated and open frame power supplies have varied mounting and package configurations.
EMC and EMI Concerns
- Most electronic equipment require adherence to meet Electromagnetic Compatibility (EMC) and Electromagnetic Interference (EMI) regulations.
- The regulation requirements ensure that the equipment does not affect the working of other equipment.
- External electrical noise will not prevent certified equipment from working properly.
- DC/DC power supplies may be certified and be in compliance with regulatory requirements.
- The complete system may be certified, but small circuits on the inside do not need certification.
Safety Requirements
- Electronic devices must meet Underwriters Laboratory (UL) standard 60950-1 and European Union (EU) standard EN 60950-1. Both set of standards are derived from the International Electrotechnical Commission (IEC) standard IEC 60950-1.
- Safety certifications are given for the end equipment.
- Certifications are not needed for the internal sub-parts but may be obtained.
- Safety certification for a power supply must be attained if a DC/DC power supply is used to isolate equipment operators from dangerous voltage.
Conclusion
- DC/DC power supplies, known as DC/DC converters, are power supplies that convert a DC voltage of a certain magnitude to one of a different magnitude to supply a device.
- DC power supplies are used with electronic devices that require DC power and are used in the Industrial, Medical, and Telecom markets.
- DC power supplies are classified into isolated and non-isolated converter topologies and are chosen based on the needs of an application.
- Isolated power supplies were driven by the telecom industry, which uses a negative (-48V) bus system for long-term reliability. Wireless systems became a major player in the communications industry.
- The need for higher efficiency and power density has resulted in smaller and higher performing non-isolated converters.
- Primary switch mode and secondary switch mode are the two types of switch mode regulated power supplies.
- A DC-DC converter is a type of DC power supply that utilizes DC voltage as an input.
- Two types of DC-DC converters are non-isolating and isolating converters.
- Operating car radio, CB transceiver, or mobile phone, running a personal CD player, energizing one of the latest CPU chips, engaging a PC power supply application, operating an electronic circuitry, providing an insulation testing voltage, running a car HiFi amplifier‘s circuitry, and engaging a DC-AC sine wave inverter application are some of the uses of DC-DC converters.
- DC power supplies have four basic outputs: constant voltage, constant current, voltage limit, and current limit.
- Battery eliminators, constant voltage power supply, constant voltage/constant current power supply, programmable supply, and multi-range power supply are the most common DC power supplies available on the market.
- When selecting a DC power supply, one should consider the following specifications: constant current and constant voltage mode, output, regulation, temperature, AC input, ripple and noise, tracking accuracy, and DC isolation.
